An Automated Design-flow for FPGA-based Sequential Simulation

In this paper we describe the automated design flow that will transform and map a given homogeneous or heterogeneous hardware design into an FPGA that performs a cycle accurate simulation. The flow replaces the required manually performed transformation and can be embedded in existing standard synthesis flows. Compared to the earlier manually translated designs, this automated flow resulted in a reduced number of FPGA hardware resources and higher simulation frequencies. The implementation of the complete design flow is work in progress.\u

NoC Emulation based on Partial Reconfiguration

This paper studies the possibly of using partial reconfiguration for achieving acceleration of the emulation process of Systems on Chip based on Networks on Chip (NoC). The main advantage of using partial reconfiguration is that re-synthesis of the systems is not required and thus the emulation process can be accelerated. The paper focuses on the description of a method for building partial runtime reconfigurable systems and its application for building a NoC emulation framework. The paper also includes a brief description of all the building elements of the emulation framework and a use case that demonstrates the advantages of the use of partial reconfiguration for emulation

Fast, Accurate and Detailed NoC Simulations

Network-on-Chip (NoC) architectures have a wide variety of parameters that can be adapted to the designer's requirements. Fast exploration of this parameter space is only possible at a high-level and several methods have been proposed. Cycle and bit accurate simulation is necessary when the actual router's RTL description needs to be evaluated and verified. However, extensive simulation of the NoC architecture with cycle and bit accuracy is prohibitively time consuming. In this paper we describe a simulation method to simulate large parallel homogeneous and heterogeneous network-on-chips on a single FPGA. The method is especially suitable for parallel systems where lengthy cycle and bit accurate simulations are required. As a case study, we use a NoC that was modelled and simulated in SystemC. We simulate the same NoC on the described FPGA simulator. This enables us to observe the NoC behavior under a large variety of traffic patterns. Compared with the SystemC simulation we achieved a speed-up of 80-300, without compromising the cycle and bit level accuracy

Network on chip architecture for multi-agent systems in FPGA

A system of interacting agents is, by definition, very demanding in terms of computational resources. Although multi-agent systems have been used to solve complex problems in many areas, it is usually very difficult to perform large-scale simulations in their targeted serial computing platforms. Reconfigurable hardware, in particular Field Programmable Gate Arrays (FPGA) devices, have been successfully used in High Performance Computing applications due to their inherent flexibility, data parallelism and algorithm acceleration capabilities. Indeed, reconfigurable hardware seems to be the next logical step in the agency paradigm, but only a few attempts have been successful in implementing multi-agent systems in these platforms. This paper discusses the problem of inter-agent communications in Field Programmable Gate Arrays. It proposes a Network-on-Chip in a hierarchical star topology to enable agents’ transactions through message broadcasting using the Open Core Protocol, as an interface between hardware modules. A customizable router microarchitecture is described and a multi-agent system is created to simulate and analyse message exchanges in a generic heavy traffic load agent-based application. Experiments have shown a throughput of 1.6Gbps per port at 100 MHz without packet loss and seamless scalability characteristics

Design of Reconfigurable Crossbar Switch for BiNoC Router

this paper presents implementation of 10x10 reconfigurable crossbar switch (RCS) architecture for Dynamic Self-Reconfigurable BiNoC Architecture for Network On Chip. Its main purpose is to increase the performance, flexibility. This paper presents a VHDL based cycle accurate register transfer level model for evaluating the, Power and Area of reconfigurable cross bar switch in BiNoC architectures. We implemented a parameterized register transfer level design of reconfigurable crossbar switch (RCS) architecture. The design is parameterized on (i) size of packets, (ii) length and width of physical links, (iii) number, and depth of arbiters, and (iv) switching technique. The paper discusses in detail the architecture and characterization of the various reconfigurable crossbar switch (RCS) architecture components. The characterized values were integrated into the VHDL based RTL design to build the cycle accurate performance model. In this paper we show the result of simple 10x10 crossbar switch .The results include VHDL simulation of RCS on Xilinx ISE 13.1 software tool

Interconnect architectures for dynamically partially reconfigurable systems

Dynamically partially reconfigurable FPGAs (Field-Programmable Gate Arrays) allow hardware modules to be placed and removed at runtime while other parts of the system keep working. With their potential benefits, they have been the topic of a great deal of research over the last decade. To exploit the partial reconfiguration capability of FPGAs, there is a need for efficient, dynamically adaptive communication infrastructure that automatically adapts as modules are added to and removed from the system. Many bus and network-on-chip (NoC) architectures have been proposed to exploit this capability on FPGA technology. However, few realizations have been reported in the public literature to demonstrate or compare their performance in real world applications. While partial reconfiguration can offer many benefits, it is still rarely exploited in practical applications. Few full realizations of partially reconfigurable systems in current FPGA technologies have been published. More application experiments are required to understand the benefits and limitations of implementing partially reconfigurable systems and to guide their further development. The motivation of this thesis is to fill this research gap by providing empirical evidence of the cost and benefits of different interconnect architectures. The results will provide a baseline for future research and will be directly useful for circuit designers who must make a well-reasoned choice between the alternatives. This thesis contains the results of experiments to compare different NoC and bus interconnect architectures for FPGA-based designs in general and dynamically partially reconfigurable systems. These two interconnect schemes are implemented and evaluated in terms of performance, area and power consumption using FFT (Fast Fourier Transform) andANN(Artificial Neural Network) systems as benchmarks. Conclusions drawn from these results include recommendations concerning the interconnect approach for different kinds of applications. It is found that a NoC provides much better performance than a single channel bus and similar performance to a multi-channel bus in both parallel and parallel-pipelined FFT systems. This suggests that a NoC is a better choice for systems with multiple simultaneous communications like the FFT. Bus-based interconnect achieves better performance and consume less area and power than NoCbased scheme for the fully-connected feed-forward NN system. This suggests buses are a better choice for systems that do not require many simultaneous communications or systems with broadcast communications like a fully-connected feed-forward NN. Results from the experiments with dynamic partial reconfiguration demonstrate that buses have the advantages of better resource utilization and smaller reconfiguration time and memory than NoCs. However, NoCs are more flexible and expansible. They have the advantage of placing almost all of the communication infrastructure in the dynamic reconfiguration region. This means that different applications running on the FPGA can use different interconnection strategies without the overhead of fixed bus resources in the static region. Another objective of the research is to examine the partial reconfiguration process and reconfiguration overhead with current FPGA technologies. Partial reconfiguration allows users to efficiently change the number of running PEs to choose an optimal powerperformance operating point at the minimum cost of reconfiguration. However, this brings drawbacks including resource utilization inefficiency, power consumption overhead and decrease in system operating frequency. The experimental results report a 50% of resource utilization inefficiency with a power consumption overhead of less than 5% and a decrease in frequency of up to 32% compared to a static implementation. The results also show that most of the drawbacks of partial reconfiguration implementation come from the restrictions and limitations of partial reconfiguration design flow. If these limitations can be addressed, partial reconfiguration should still be considered with its potential benefits.Thesis (Ph.D.) -- University of Adelaide, School of Electrical and Electronic Engineering, 201

From MARTE to Reconfigurable NoCs: A model driven design methodology

Due to the continuous exponential rise in SoC's design complexity, there is a critical need to find new seamless methodologies and tools to handle the SoC co-design aspects. We address this issue and propose a novel SoC co-design methodology based on Model Driven Engineering and the MARTE (Modeling and Analysis of Real-Time and Embedded Systems) standard proposed by Object Management Group, to raise the design abstraction levels. Extensions of this standard have enabled us to move from high level specifications to execution platforms such as reconfigurable FPGAs. In this paper, we present a high level modeling approach that targets modern Network on Chips systems. The overall objective: to perform system modeling at a high abstraction level expressed in Unified Modeling Language (UML); and afterwards, transform these high level models into detailed enriched lower level models in order to automatically generate the necessary code for final FPGA synthesis

Implementation and Evaluation of an NoC Architecture for FPGAs

The Networks-on-Chip (NoC) approach for designing Systems-on-Chip (SoC) is currently emerging as an advanced concept for overcoming the scalability and efficiency problems of traditional bus-based systems. A great deal of theoretical research has been done in this area that provides good insight and shows promising results. There is a great need for research in hardware implementation of NoC-based systems to determine the feasibility of implementing various topologies and protocols, and also to accurately determine what design tradeoffs are involved in NoC implementation. This thesis addresses the challenges of implementing an NoC-based system on FPGAs for running real benchmark applications. The NoC used a mesh topology and circuit-switched communication protocol. An experimental framework was developed that allowed implementation of NoC-based system from a high level specification, using the Celoxica Handel-C hardware description language. Two test applications: charged couple device (CCD) and JPEG were developed in Handel-C to be used as our benchmark applications. Both benchmarks are computational expensive and require large quantities of data transfer that will test the NoC system. Implementation results show that the NoC-based system gives superior area utilization and speed performance compared to the bus-based system, running the same benchmarks